The owner of this guestbook has (temporarily) disabled adding new messages.
-
5:41pm 10-15-2010Feliks
-
WIND CAR
My version of car wind.Solo of trumpet
Will test whether it could be faster than the wind... Boat too....
You never know what is beyond the present ... :rolleyes:
ICE RACE
But faster than the wind, it is possible ....
But perhaps the experience of the Ice Race can to help you change the aerodynamics in F1?
But in F1, there are winds above 300 km / h !
Fighter aircraft F-104 starts at a similar velocity. Right then, about 700 KG per 1 square meter load.
If using a well-sculpted are did the 700 KG used to accelerate boild F1 ......
I think that not everything has been said in the aerodynamics of F1.....
700 KG at 1 m^2 - 70 KG forward at 10 dcm^2 aditional F1 wings....
Regards Andrew:
-
10:17am 10-07-2010Feliks
-
I simply will look as flat block. It can be cast as a single unit. It did not need the division on the block and head. Because the pistons can be put at the bottom......
It is full 4 stroke engine.
It is first flat diesel engine.
Regards Andrew
-
12:58pm 09-27-2010Feliks
-
A new way of sailing through a balloon which has the wind, and transmits energy to the propeller using hydraulics
And sailing version of the Venturi jets:
Regards Andrew
-
3:15pm 09-17-2010Feliks
-
Next Dixieland :
In some tubes can be hidden anti-missile ..
Mistake..!!
Regards Andrew
-
3:14pm 09-17-2010Feliks
-
Rotating Dixieland Yoda.
Regards Andrew
-
12:49pm 09-15-2010Feliks
-
Name : Jazz Big Band
Regards Amdrew
-
12:51am 09-15-2010Feliks
-
There is a way to shorten a bit of flexible hydraulic tube...
Well, if it accidentally escaped gas from the balloon and so it can be
Regards Andrew
-
10:25pm 09-12-2010Feliks
-
Of course, two rotate in one direction and two in the opposite direction.
You must use a very light hydraulic oil. If it were not frozen in winter.
Hydraulic pump in the balloon has the best power to weight ratio. All the airlines are working on the hydraulic actuators.
Of course, all of the balloon must be tested in the wind tunnel aerodynamic, in order to fully match the efficiency of the 21st century.
Some pictures of how to create a balloon from the inside :rolleyes:
and NASCAR wind tunnel
Regards Andrew
-
1:50pm 09-08-2010Feliks
-
The first windmills pumped water in America. To sustain this good tradition, I developed a little more modern sytem for the production of electric current in a similar way of pumping water.Whether American landscape views, are water sphere.I decided to add this view to the next shot where the water will be collected water so that it could give electrical energy when draining it back into the lower reservoir.
This water will be pumped sphery as in the first versions of windmills, wind.
The wind turbine will move a small diameter, but it is a multi-blade, placed together with the hydraulic pump in the middle of a specially constructed balloon. Balloon will be tethered, as previously barrage balloons.
Only that will go along the line, hydraulic pipes, the hydraulic motor, which will be driven water pump located in the lower reservoir.The water pump will continuously pump water to sphery. Now the water falling from the lower reservoir back to the shery, will do an electric current through hydrogenerator.
Every so water sphere about the capacity of 2000 m 3, and the height 100 m can give power 10 MW for 3 minutes. If filling pumps water with the one I believe loss is managing to fill waters up, we will have it 10 MW driven with wind turbine in balloons.
Of course, the balloons could be filled up by hydrogen, because today we have very good material on the shell.
This system could be installed in any place where electricity is needed, and thus would have limited losses on the transfer.
Also low noise, and the invisibility of the rotating blades, not to interfere in coexistence with the environment.Balloons can be affixed to a height of 150 to 200 meters, where the wind is always blowing on the ground even when there is absolute silence.
Regards Andrew
-
10:45am 09-01-2010Mohammed Al Maghrabi
-
Hi Mr. Andrew felik How are you? hope you are fine
This is Mohammed from Saudi Arabia, Riyadh, College of Engineering, Mechanical Engineering, King Saud University
I've seen your invention while i'm surfing google, i showed your web site to my professor and he asked me to study and apply your invention in my graduation project, i started to gather informations about conventional internal combustion engines , after that i extracted some information from your web site >> do not worry i've mentioned that this invention was invented by a polish scientist, after that, me and my colleagues went to a factory for manufacturing the two pistons in your invention, we finished them and they cost us arround $ 3500, unfortunetly the engine did not work due to a lot of mistakes in design >>mistakes in Finite element analysis for the ignition temperature.
I informed you about all that just to make you feel happy that a lot of people arround the world are studying your invention, also to thank you for all the informations provided in your web site.
Your sincerely Mohammed
-
2:55am 08-16-2010peter
- i think i should see the actural movement of a engine
-
10:38pm 08-14-2010Feliks
-
However and that will had such a good humor, just take a timber and a little grease lubricated.
Do not need any oil !!
Seal or Teflon or lubricated with diesel fuel.
OIl = diesel fuel in this picture
Regards Andrew
-
10:17am 08-12-2010Feliks
-
I think that this technology is very effective. Can you imagine that by doing the same movement up and down through the traditional piston-connecting rod-crankshaft to get the same ease the movement of this vehicle?
I think that it would then be much harder work. And these four , the looks on it, they not liked to work more than need....
Can you feel it ??
Regards Andrew
-
9:56pm 08-11-2010Feliks
-
I also very close to the Technology
Regards Andrew