The owner of this guestbook has (temporarily) disabled adding new messages.
Message:

4:24pm 10-11-2015
Feliks
So now even a version
So here the animation ramjet engines between the wings in a spoon effect, which is about 9 times increase input speed .. Pipes of course without turbines, such as SR 71, and, so to eye with 250 MW of getting So, yes, the set of a diameter of 30 meters, having the 250 MW of power, he would have 12 pieces of such pipes since SR71, visible starter pneumatic boot, and the number 2 units would give so much energy around, a small nuclear power plant Only with the size of the power plant, even coal, consumed for own use 50 MW (high pressure pumps, blowers and fans, etc.). Here only the minimum energy for the fuel supply system, expressed in kilowatts ..
And the cost of investment that air football field, probably will be significantly smaller.
It's to improve the imagination, what I'm saying.
Well, here we have any fuel - coal dust, gas, oil.
6:36pm 10-01-2015
Feliks
And you know what these wings including my project still can be used? not even suppose ...:rolleyes:

This is EXHAUST. ..
Thus, the negative pressure is created dam that will serve to suck exhaust gas from the engine .. vacuum will remain on throughout the exhaust pipe .. will suck exhaust lot better than they do, competitive exhaust pipe curled in a "sausage" ...
And by the way a negative pressure can be so great that at some considerable speed, you can turn off the ignition .. and cut off the supply of fuel .. interesting at what it will speed ..:rolleyes:

and even before up to speed, it also can underpressure to run a turbine from the exhaust and nwtedy that the system does not have to be connected ..

Well, not to mention the alternator, which also would say fueled rotary vane pump on the vacuum ...

Yes, if so, a pair of wings spoon should be at the back of the car ....

6:35pm 10-01-2015
Feliks
Here the newest model ..

4:13pm 08-12-2015
Feliks
[QUOTE=Thepanzerfuhrer;32937258]If I employed this wing technique on say a convertible mustang, how much reduction could I expect in my corrected et?[/QUOTE]

for it is not such a simple thing .. My drawing is only a theory, and even to good its use probably still need many experiences .. It's like a first flight .. Here we see that one of the first aircraft was driven by the wheel to become independent by the wind .. https://en.wikipedia.org/wiki/Gustave_Whitehead
Now that the simulator airfoil from NASA perfectly we can see that even minimal changes in some parameters, the cause, the whole project can not go wrong .. You can discern that the value of lifting force to the resistance can take very extreme value. THEREFORE should be chosen carefully all the values. RELATIONSHIP TO RESISTANCE to the lift of WAS AS 1: 10 ..
For the time being we do not have a simulator to "spoon effect", the distance and angle of attack of wings .. But we can assume based on experience, that it will have a value, after careful about choosing the least 3 times larger than the two single wing, that is, if we simulator one wing lift 37 pounds is two give us 74 pounds .. multiply it by spoon effect. that is, times 3, which gives us 222 pounds of force "propellants", in relation to the resistance, which is 7.4 pounds ... So theoretical gain is about 30 times .. Now, from our skills and experience will depend on how much practically with the profit we will they could utilize to drive a car .. it is a very big number, and even if almost ten times we reduce it, it will be us coefficient 3, for a clean drive a car .. so it all depends on how it practically execute ..

4:12pm 08-12-2015
Feliks
Here this car..



Andrew
4:12pm 08-12-2015
Feliks
Yesterday marked the 70th anniversary of explosion atomic bomb in Nagasaki. the first theoretical founder Joseph Rotblat it was ..

https://www.wagingpeace.org/tag/joseph-rotblat/

quoted below what was his attitude to scientific discoveries:

"Hind al. [16] pointed out that the unpredictability switched
petent research makes such a project
difficult, if at all possible. But such a project
of it becomes meaningful if based on ethical principles.
Rotblat was of the opinion that the foundations of ethics should form
part of the training of all scientists. He wanted,
that universities have adopted some sort of cited above
oaths, and to students of natural filed
such a vow when finish their studies, and listened to lectures
on the ethical aspects of science. Relying on his conscience
and the good will of individual scientists not in itself
It will be sufficient, since the units are often unreliable.
Therefore called for the establishment of a number of ethics committees,
which might consider science projects that may affect
human life, some kind of medical committees
ethical. Consent ethics of such a committee would be required
for funding a particular direction of research.
In later life, Rotblat opposed
research conducted in secret, which is often
in the case of government research and industrial applications. He believed
that new knowledge to be shared. He moved a problem
associated with the commercialization of research, since many studies
carried out in universities were funded
from commercial sources. This could influence the direction
study, put at risk the ethical problems and increase the mystery.
He also began to hate the patenting of results
research, because in his opinion, knowledge should be
available for free. But scientists themselves often impose secrecy.
because they want to keep other scholars in the dark
until publication, because a person who
First it publishes, often gets awards and honors.
These views Rotblat that come with early stages
his career and matured over a lifetime, are a bit naive,
because competition, secrecy
and commercialization are part of learning. He simply wanted
resist these pressures "

I like it..

Andrew
9:55pm 08-02-2015
Feliks
Once upon a time there was no internet .. Even with the video was difficult .. only movies .. I have survived such films showing such beautiful cars with large wings .. I once suggested that such a wing but the bulge facing down ..but not all of it like .. it turned out that such huge wings were already in use .. Now can a wing of such large dimensions but the double - spoon effect .. interesting how many vacuum that could, if NACA-profile Felix apply any .. maybe above a certain speed .. .....





Andrew
6:05pm 07-26-2015
Feliks
We must take care to harmful aerodynamic resistances as low as possible ..
Because, after all, and two revolutions per second can turn the wings .. It is 120 km / h .. Pretty on the wind.
This cover should be good.



Can of some use ..

http://enu.kz/repository/2010/AIAA-2010-1007.pdf

Andrew
3:02am 07-23-2015
Feliks
Windmills are good, but you need a wind to their work ...
But here the way we can, even in a closed room, well, for instance in the basement of the house, "produce wind" .. Just, the Starting a device, manually, to the speed of 18 m / sec..To are few, it is 1 turn per second.
I've been to all these wings Windmill Red Baron, will operate the wind, at the speed of 18 m / sec ..
If we consider, in simulator NASA and the effect of "spoon" is theoretically You will receive an strength of resistance to "lift force" (vacuum). and is about 15 times less ..
So the resistance force, it is only around 6% received "lift force"
I think that even with a very negligent and mismanagement execution of such a machine, it will propel herself after the first start-up .. And we should still get some electricity .. Case, jet just how much ..



description:



Vane drive:



http://www.new4stroke.com/treadmill.mp4

or

Regards Andrew
4:04pm 07-04-2015
Feliks
So once again we return to the thermodynamic efficiency new4stroke .. Here the hearing of the efficiency of the charts made for the traditional engine.
https://www.mhi.co.jp/technology/review/pdf/e451/e451021.pdf

You can see on the chart with the highest efficiency is low speed engine sea, which is 47%.
My engine as reported above, draws about 360 cc more than the old conventional engine, which did a prototype or 600 ccm ... But this extra volume displacement, is implemented by the system of pistons which rotate two times slower, ie, the force of inertia are four times smaller, because they are dependent upon the square of the rotation. that is, we can just to count the inertial forces relative to the sucked air further. 360 ccm divided by four is going to give us 90 cc. These 90 ccm going to beat the additional forces of inertia (ie a total of friction). But now we have a net profit of 360 ccm minus 90 cc = 270 cc. It is pure extra profit aspirated air, without any mechanical losses already on its construction .. that is entirely theoretical operational efficiency engine so it looks .. traditional engine of 600 cc is 47%, ie 12, 76 ccm is 1% plus an additional 270 cc, which is 270 divided by 12,76 = 21% additional efficiency .. So the total increase the efficiency regarding displacement capacity should be at 47 +21 = 68%. additionally, we can still make a profit energy by stopping propelling Similar systems poppet valves and springs which will have at least the 7% efficiency more .. So, the total physical ability of such an engine 68% + 7% = ~ 75% .

ie it is to increase efficiency, which can not be subject to discussion.

If we add all the above mentioned advantages, no such low temperature in the combustion chamber, the combustion speed, and more, which can contribute to higher efficiency even further by around 5% this will give us the final number of efficiency of up to 80% .....
Andrew
12:01pm 04-23-2015
Feliks
Another one..
Such experience existing in the Museum of Aviation, showing the magnitude of the resistance of various airfoil, by replacing and inserting a rod, profiles of different thicknesses .. I used it to show the enormous size of the vacuum between the two profiles airlines, facing each other, "stomachs" .. So yes went my experience: first suspended weighed on an electronic scale, which is the size of kilograms of force needed to raise the single wing slid over to the bars .. turned out that about 300 Grams. that is to pick up all the rods and wing forces need 300 Grams vacuum. Applying a second similar profile, "belly" to that, at the time of blowing "wind" velocity of about 10 km / h. effects can be seen in the movie .. The strength of the vacuum, causing such rapid weight increase this up must have a value of about 1000 Grams (1KG) .. The Wing has a length of about 30 cm, on that basis, I present a first estimate of the forces in the world .. Namely, when length of about a meter, such wings, this force would have a value of about 3 KG ... or even if only 30% of the force could be used in Windmill Red Baron, its size would be about 1 KG with wings 1 meter .. Now you can try to calculate much larger projects, estimated at least ..

https://youtu.be/-kH6sdSjTrc


Andrew
12:44am 04-16-2015
Feliks
Here, the film made using the experience to lift air wing. So yes, at the beginning of the film can be seen in the enclosure fan that blows the wind a piece of the wing, cut the stropianu, and nałożonegona these two metal rods that utzrymuja it in a horizontal position and transferred to the balanced Machinery with electronic scales, which shows the size of the wing lift when the wind blows at him with a fan .. size of this force is minimal and barely can observe the movement of machinery. The experience is best several possible KINDS wings of varying thickness profile, which can be changed in a device measuring and watch the size of the lift (which produces leaf vacuum) .. Thanks to this I like the wing of a set of experiments, it turned around and walked to the wing installed on your device . The wind from the fan created between them, comparatively very high vacuum. This vacuum is so huge that in gets called when I wanted to raise above the upper wing, lower, despite a solid metal load measuring machine, also raised very high up. This example shows that the strength of Spoon Effect, is several times greater than the single wing lift force, and thus, it is possible to use the vacuum between them several times larger ....
You see, with my theory, practice works well also..

https://www.youtube.com/watch?v=u1q2TbRAZXk&feature=share

12:01am 03-05-2015
Feliks
Now why I summoned Riccardo..Ricardo developed fairly firebox V-Comet .. Especially in diesel played a significant role - helped make a high speed diesel engine .In my also applied the swirl chamber, knowing about its merits. The eyebrow appearances, this is what you see on the animation, this is not the combustion chamber. It is only the cross section through the center of the engine combustion .Komora., At the rear, with the cross-sectional view as seen in the picture, it is a channel connecting the piston "sucking" piston "exhaust". Flows this way the entire load of fuel and air, but it achieves a very high speed, which in the initial attempts resulted in taking ionized air from between the spark plug electrodes and prevented the formation of spark .Only after a magnification of this channel, began to develop a spark. If sweeping spark plug, this place was a diesel injector, it would be very beneficial ,, because after falling into the space above the small pistons with a very high speed, it would be very intense spin and excellent mixing of fuel and air. I think it is possible to build a high speed diesel, well, up to 10 000 RPM. Also on gasoline this spinning is beneficial and Ground your walls on the smallest piston, is probably the smallest of the previously used, and the heat losses are the smallest .Also at such a high speed of rotation of the smallest piston samozapłonów foci formation will be very difficult. Apart from this place, burning virtually runs elsewhere, because the distance between the planes must be greater than two millimeters in height, so that there could arise a flame. In total combustion occurs with forced intensive centrifugation only over a small piston in the cylinder least .. This is the very Riccardo improved swirl chamber, with the movement of loads in one direction and forced mechanically great speed of combustion. Looking only at the same animations, we are not able to notice it all properly. Today on the combustion chamber.

http://www.new4stroke.com/blockspark1.jpg


5:15pm 03-03-2015
Feliks
Here another video. The world's first Aerodynamics effect acting through blowing mouth. After puff heard hitting one wing of the second, and it's a loud ..



The pictures show the device to adjust the distance and angle between the wings
Yet research curiosity. Windmill spins better when opening the other wing is not blocked ..

..







Andrew
4:44pm 02-28-2015
feliks
Next video of the Red Baron Windmill prototype "Effect spoons" ... Now, despite the simplicity of the prototype and are not necessarily matched the gap between the wing and the small fan, already takes off at a speed of 25 km / hour or 7 m / sec wind speed. At 40 km / h, the fan spins very quickly., Much better. than in the experiment with a single wing ..

Messages: 61 until 75 of 421.
Number of pages: 29
Newer2 3 4 [5] 6 7 8Older